Best Tungsten for TIG Welding Stainless Steel: Type, Size and Grind

TIG torch with a pink ceramic cup and a sharply ground tungsten above a brushed stainless steel butt joint, blue-tipped lanthanated tungstens beside it

For TIG welding stainless steel, use a 2% lanthanated (blue) tungsten on DCEN. 1.5% lanthanated (gold) and 2% ceriated (grey) work just as well, and ceriated is slightly easier to start at very low amps on thin sheet. 2% thoriated (red) also welds stainless well, but it is radioactive and its grinding dust is a hazard, so most shops have moved away from it. Pure tungsten (green) and zirconiated (white) are made for AC aluminum work and are the wrong choice for stainless. This guide covers the colour codes, which size to use for your amperage, how to grind the point, and what to do when the tungsten gets contaminated.

Quick answers

  • Best all-round choice: 2% lanthanated (blue tip) is the best all-round tungsten for TIG welding stainless steel on DCEN.
  • Good alternatives: 1.5% lanthanated (gold) and 2% ceriated (grey) both work well on stainless, and ceriated starts easily at low amps.
  • Avoid thoriated if you can: 2% thoriated (red) welds well but contains radioactive thorium oxide, and its grinding dust should not be breathed in.
  • Not for stainless: Pure tungsten (green) and zirconiated (white) are AC electrodes for aluminum and wander on DC.
  • Common size: A 1/16 in (1.6 mm) tungsten covers most thin stainless sheet, and 3/32 in (2.4 mm) covers most work from about 3 mm up.
  • Grinding: Always grind the tungsten lengthwise to a point, on a wheel used only for tungsten, then leave a tiny flat on the tip.
  • Dipped it? Stop, break or grind off the contaminated end and regrind. Welding on with a dirty tungsten gives an unstable arc and dirty welds.

Which tungsten to use for stainless steel

Stainless steel is TIG welded on DCEN (direct current, electrode negative). On DCEN most of the heat goes into the work, and the tungsten stays relatively cool, so it can hold a sharp point. What you want from the electrode is easy arc starts, a stable, focused arc at both low and medium amps, and a point that lasts. The oxide-doped tungstens (lanthanated, ceriated, thoriated and rare-earth blends) all do this. Pure and zirconiated tungsten don’t hold a point well on DC, which is why they’re kept for AC.

Tungsten Tip colour (AWS A5.12) On stainless (DCEN) Notes
2% lanthanated (EWLa-2) Blue ✅ Best all-round choice Easy starts, stable arc across a wide amperage range, no radioactivity. Also works on AC inverters.
1.5% lanthanated (EWLa-1.5) Gold ✅ Excellent Behaves almost the same as 2%; some welders prefer it on AC/DC machines.
1% lanthanated (EWLa-1) Black ✅ Good Less common; works, but 1.5% or 2% is easier to find.
2% ceriated (EWCe-2) Grey (orange in older editions) ✅ Very good, especially on thin sheet Starts easily at very low amps; a good choice for thin sheet, tube and small parts. Can erode faster at high current.
Rare-earth blends (EWG) Varies by maker ✅ Good Mixtures of oxides (often lanthanum, yttrium, zirconium) sold as general-purpose AC/DC electrodes. Check the maker’s packaging for the colour.
2% thoriated (EWTh-2) Red ⚠️ Works well, but avoid if you can Was the traditional DC choice. Thorium oxide is radioactive; the main risk is inhaling grinding dust. Still specified in some qualified procedures.
Zirconiated (EWZr-1) Brown (white for the ISO 0.8% type) ❌ Not for stainless Balls on AC for aluminum and magnesium. Point doesn’t hold on DC.
Pure tungsten (EWP) Green ❌ Not for stainless AC on older transformer machines for aluminum. Arc wanders and the tip melts on DCEN.

The real differences between lanthanated, ceriated and rare-earth tungsten on stainless are small. Pick one, learn how it behaves, and stick with it. If you also weld aluminum on an inverter machine, a 2% or 1.5% lanthanated electrode covers both jobs. For an overview of TIG compared with MIG and stick for stainless, see our stainless steel welding guide.

Gloved hands grinding a TIG tungsten electrode lengthwise along the rim of a bench grinder wheel, sharpened tungstens on a stainless tray
Grind tungsten lengthwise, with the marks running toward the point, on a wheel used only for tungsten.

Tungsten colour codes: AWS and ISO

Tungsten electrodes are identified by a painted band or tip. In North America the codes come from AWS A5.12; in Europe and much of the rest of the world from ISO 6848 (EN ISO 6848). The colours for the common types match, but the names differ, and a few older or less common grades don’t line up exactly.

Type Oxide content AWS A5.12 ISO 6848 Colour
Pure tungsten None EWP WP Green
1.5% lanthanated About 1.5% La₂O₃ EWLa-1.5 WL15 Gold
2% lanthanated About 2% La₂O₃ EWLa-2 WL20 Blue
2% ceriated About 2% CeO₂ EWCe-2 WC20 Grey
2% thoriated About 2% ThO₂ EWTh-2 WT20 Red
Zirconiated About 0.8% ZrO₂ (ISO) EWZr-1 (brown) WZ8 White (ISO)

Colours can vary between brands and editions of the standards, especially for ceriated (once orange) and for blends. When in doubt, read the classification printed on the box rather than trusting the colour alone.

Why thoriated tungsten is being phased out

For decades, 2% thoriated (red) was the default DC tungsten, and it still welds stainless very well. The problem is the thorium oxide: thorium is a naturally radioactive element that emits alpha particles. Alpha radiation can’t get through skin, so holding or welding with a few electrodes is a very low risk. The real concern is grinding. Grinding produces fine dust with thorium oxide on it, and if that dust is breathed in, it stays in the lungs and keeps irradiating tissue from the inside.

If you do use thoriated tungsten (for example because a qualified welding procedure requires it):

  • Grind on a dedicated grinder with local dust extraction, or buy electrodes pre-ground.
  • Wear a suitable dust mask or respirator while grinding.
  • Clean around the grinder with a vacuum (ideally HEPA) or damp wiping, not by blowing or sweeping.
  • Collect grinding dust and stubs and dispose of them according to local rules.

For most stainless work, there’s no welding reason to keep using thoriated. 2% lanthanated or 2% ceriated gives the same or better results without the dust hazard, which is why many fabricators, schools and employers have switched.

Tungsten size by amperage

Choose the tungsten diameter for the current you’ll actually use. Too thin, and the tip overheats, balls up or spits tungsten into the weld. Too thick, and the arc is hard to start and wanders at low amps. Stainless usually needs a little less current than mild steel of the same thickness, so smaller tungstens cover a lot of stainless work.

Tungsten diameter Practical DCEN range (starting point) Typical stainless work
0.040 in (1.0 mm) About 10–60 A Very thin sheet (0.5–0.8 mm), foil-thin edges, small tube
1/16 in (1.6 mm) About 20–120 A Sheet from about 0.8 to 2 mm; the most-used size for thin stainless
3/32 in (2.4 mm) About 80–200 A About 2–6 mm sheet and plate; a good general-purpose size
1/8 in (3.2 mm) About 150–300 A Thicker plate, heavy root and fill passes

These are practical starting points for lanthanated or ceriated tungsten on DCEN. Manufacturer charts often list higher maximums, especially for the small sizes; staying a little under them keeps the point sharp for longer. For matching current to sheet thickness, see the settings table in our TIG welding stainless steel settings guide, and the stainless steel gauge chart to convert gauge to millimetres.

How to grind tungsten for stainless

On DCEN, the shape of the tip shapes the arc. A clean, sharp, concentric point gives a focused, steady arc; a badly ground point makes the arc wander.

  1. Use a dedicated wheel. Grind tungsten only on a wheel (or a tungsten grinder) that is never used for steel or other metals. Steel particles picked up from a shared wheel contaminate the tip.
  2. Grind lengthwise. Hold the electrode so the grinding marks run along its length, toward the point, not around it. Circular marks make the arc jump and wander.
  3. Make the taper about 2 to 2.5 times the diameter long. On a 3/32 in (2.4 mm) electrode, that’s a taper roughly 5–6 mm long, which works out to an included angle of roughly 20–30°.
  4. Leave a tiny flat. Lightly touch the very tip to the wheel to take off the needle point. A small flat stops the tip from breaking off into the puddle and lasts longer, especially above about 100 A.
  5. Rotate as you grind to keep the point centred, and don’t overheat the electrode.
  6. Set the stickout. With a standard collet body, a stickout of roughly 3–6 mm (1/8–1/4 in) is typical. A gas lens lets you run longer stickout for corners and fillets.

Point angle and the weld bead

Tip shape Arc and bead Use it for
Sharp (small included angle, long taper) Easy starts, wider arc, shallower penetration Thin sheet, low amps, outside corners
Medium (around 30–45°) Balanced arc and penetration General sheet and plate work
Blunt (larger angle, short taper, small flat) Narrower, more focused arc, deeper penetration, longer tip life Higher amps, thicker material, automated welding

Don’t snap off a tungsten by notching it on the wheel and breaking it: the break is often uneven and can crack the electrode. Cut it, or grind it back cleanly.

Tungsten contamination: causes and fixes

A contaminated tungsten is the most common reason a stainless TIG arc suddenly turns wide, erratic and dirty. The tip looks balled, blackened or coated, and the weld picks up soot, oxides or tungsten inclusions.

What you see Likely cause Fix
Silver or grey blob on the tip after a “pop” Tungsten touched the puddle or the filler rod Stop, break or grind off the contaminated end well past the blob, and regrind. Don’t keep welding on it.
Blue, purple or black tungsten after welding Not enough post-flow, or gas flow too low Increase post-flow so the tungsten cools under argon (a common rule is about 1 second per 10 A, minimum several seconds).
Balled tip on DCEN Tungsten too small for the amps, wrong type (pure/zirconiated), or machine set to DCEP Use a larger oxide-doped tungsten and check the polarity.
Arc wanders from side to side Rough or circular grind marks, off-centre point, or dirt on the tip Regrind lengthwise on a clean, dedicated wheel.
Tungsten inclusions in the weld Tip breaking off, too much current for the size, or a dipped tungsten Leave a small flat, size up, and regrind after any touch.

Clean filler rod and base metal also protect the tungsten. Wipe the joint and rod with acetone or isopropyl alcohol and use stainless-only brushes, as covered in the welding guide’s step-by-step section.

Cup size, gas lens and shielding gas

The tungsten works together with the torch front end. For stainless:

  • Gas: 100% argon is the standard TIG shielding gas for stainless. Flow of roughly 7–10 L/min (15–20 cfh) suits most standard cups; larger cups and gas lenses may need more.
  • Gas lens: A gas lens smooths the gas flow so the shield is less turbulent. That lets you use a longer tungsten stickout and gives better coverage, which helps keep heat tint down on stainless.
  • Cup size: A common rule is a cup inside diameter of at least about 4–6 times the tungsten diameter. Size 6–8 cups are typical on thin stainless; larger cups give more coverage on wider beads.
  • Back purge: On tube, pipe and anything where the back of the weld matters, purge the inside with argon to prevent “sugaring” (heavy oxidation on the root side).

Weld colour shows how well the shielding worked. Straw to light gold is generally fine for most uses; dark blue, grey or black means oxidation that reduces corrosion resistance. See the stainless steel weld color chart for what each colour means, and cleaning stainless steel after welding for removing heat tint.

Quick setup by job

Job Tungsten Tip Notes
Thin sheet (0.5–1.5 mm), 304 or 316 1/16 in (1.6 mm) 2% lanthanated or 2% ceriated; 0.040 in for the thinnest Sharp point, tiny flat Low amps, tight fit-up, pulse helps. See the stainless sheet guide for choosing the sheet.
Thin-wall tube and exhaust 1/16 in (1.6 mm) 2% lanthanated Sharp point Back purge the inside. See welding stainless exhaust.
3–6 mm plate 3/32 in (2.4 mm) 2% lanthanated Medium point, small flat Multi-pass on the thicker end.
Thick plate, high amps 1/8 in (3.2 mm) 2% lanthanated Blunter point, flat Consider argon-helium for a hotter arc.
Stainless to mild steel Same as for the stainless thickness As above Use 309L filler. See welding stainless to mild steel.
Duplex 2205 2% lanthanated or ceriated As above Controlled heat input and 2209 filler. See welding duplex 2205 to 316.

The tungsten type doesn’t change with the grade: 304, 316 and their low-carbon “L” versions all weld with the same tungsten. Grade affects the filler (308L for 304, 316L for 316). For grade differences, see 304 vs 316 stainless steel, 304 vs 304L and the stainless steel grades guide.

Frequently asked questions

What colour tungsten is best for stainless steel?

Blue (2% lanthanated) is the best all-round choice for TIG welding stainless on DCEN. Gold (1.5% lanthanated) and grey (2% ceriated) are equally good options. Red (2% thoriated) works but is radioactive, and green (pure) and white (zirconiated) are for AC aluminum work.

Is lanthanated or ceriated better for stainless?

Both work very well. Ceriated starts slightly more easily at very low amps, which helps on thin sheet and small parts. Lanthanated holds up better across a wider current range and is the more versatile choice if you also weld aluminum on an AC inverter. For most welders the difference is small.

Can I use thoriated tungsten on stainless steel?

Yes. 2% thoriated welds stainless very well on DC, and some qualified procedures still call for it. The concern is health: thorium oxide is radioactive and its grinding dust shouldn’t be inhaled. If you use it, grind with dust extraction and a mask, or buy pre-ground electrodes. Otherwise, lanthanated gives the same results without that risk.

Can I use pure (green) tungsten on stainless?

It isn’t recommended. Pure tungsten doesn’t hold a point on DCEN; the tip melts into a ball and the arc wanders. It’s designed for AC welding of aluminum on transformer machines.

What size tungsten should I use for 16 gauge stainless?

16 gauge stainless is about 1.5 mm thick and usually welds at roughly 50–80 A on DCEN, so a 1/16 in (1.6 mm) tungsten is the usual choice, with a 1/16 in filler rod.

Should a tungsten for stainless be sharp or balled?

Sharp. On DCEN, grind a point lengthwise and leave a tiny flat on the end. A balled end is an AC technique for aluminum on older machines; on DC it gives a wide, unstable arc.

How often should I regrind the tungsten?

Whenever it touches the puddle or the filler rod, or when the arc starts to wander or the tip looks discoloured or rounded. A clean tungsten on a steady arc can run a long time between grinds; a dipped one should be reground straight away.

Last updated: November 2026. Colour codes follow AWS A5.12 and ISO 6848 for the common types; check the classification on the box, as colours can vary by edition and brand. Amperage ranges are practical starting points, not limits; follow your machine maker’s chart and any qualified welding procedure.

Sponsored

Related posts